Bulk glass a winner at Kendall-Jackson Wine Estates
Jack Mans, Plant Operations Editor -- Packaging Digest, 8/1/2012 2:04:00 AM
Kendall-Jackson Wine Estates, Santa Rosa, CA, totallyrevamped its bottling operations recently with a switch to bulk glass receiving and the redesign of the two bottling lines in its plant. Both lines run 750-mL bottles, and Line 1 also fills 375-mL bottles. Running at speeds from 180 to 240 bottles/min, the lines are now among the most automated in the wine industry.
One of the key motivators of the project was Kendall-Jackson's interest in converting to bulk glass. Kendall-Jackson had always received its wine bottles in reshippers, but these have numerous disadvantages. Depalletizing cases of glass is a labor-intensive process that can cause injuries and damage cases and partitions.
In comparison, bulk glass has significant cost savings. Tom Barnes, Kendall-Jackson's director of botling, says, "The new bulk glass lines allow us to reduce our transportation costs. Bulk glass allows us to haul between 2,600 and 3,000 cases of empty glass vs 2,300 cases of glass in shipping cases." He explained bulk bottles on pallets allows vendors to store less glass because they don't have to store bottles in cases designated for a specific type of wine.
Kendall-Jackson decided to upgrade its existing bottling lines as part of the project, and Emmeti offered turnkey design and installation proposals. It was awarded the project based on the amount of equipment it was providing and its line design and controls.
This turned out to be a prudent decision. Barnes says, "We are very pleased with Emmeti's commitment to make the project a success. Emmeti worked very closely with us on design. Its team of installers worked very long hours to install the equipment in a small time window. The Emmeti engineers stayed on site and fine tuned the equipment to achieve the 90 percent efficiency guaranteed in the contract."
To start the process, Emmeti developed a line layout that reused as much of the existing conveyors as possible. This allowed Kendall-Jackson to benefit from new lines, while still using selected pieces of conveyor and some of its other existing machines, thus reducing project costs, while incorporating advanced technology to run at high efficiency.
Emmeti also supplied much of the other new equipment installed on the lines, including the bulk depalletizers, automatic case packers, continuous bottle dividers for the packers and the bottle accumulators after the fillers. All conveyors and other equipment supplied by Emmeti to Kendall-Jackson use high-efficiency motors that conform to Eff 1 standards set by the European Committee of Manufacturers of Electrical Machines and Power systems (CEMEP), thus reducing energy usage of the line.
Kendall-Jackson installed Emmeti's Lobster model depalletizers on both bottling lines. Pallets of bottles, which are supplied by O-I and Saint-Gobain North America, are delivered to the depalletizer infeed by forktruck and are placed on the infeed conveyors, where workers remove plastic covering the bottles and restraining straps.
The pallets are raised to the upper discharge platform where the machine transfers bottles, one layer at a time, to the receiving table. The Lobster depalletizers remove most of the bottles at the winery using a sweep-type head. For reverse-tapered bottles, or bottles that should not have shoulder-to-shoulder contact, the depalletizers pick up the bottles with inflatable tubes and place them on the discharge conveyor. The depalletizers can handle 2.5 layers of glass per min.
The Emmeti depalletizers are designed to recall any pallet pattern programmed and stored in the touchscreen operator console. Kendall-Jackson receives some of its bulk bottles inside dividers and/or partitions, and Emmeti's pick-and-place head is designed to receive and remove these bottles from inside the dividers, after which the head picks up the dividers and moves them into the appropriate dunnage magazine.
Depalletized bottles are single-filed and are then picked up by their necks for tramsport to the fillers. Emmeti's variable-speed conveyors minimize back pressure to reduce bottle scratching or tipping and ensure a smooth transition from mass flow to single file.
CLEANER/FILLER/CORKER IN AN ENCLOSURE
Kendall-Jackson installed a new cleaner/filler/corker from Gruppo Bertolaso S.p.a. on Line 1 and used an existing Krones Inc. cleaner and existing filler/corker from Gruppo Bertolaso on Line 2. In both cases, the units are housed in an enclosure.
A continuous conveyor transports the bottles through the enclosure and bottles are diverted from it at each machine and back onto it at the exit of each machine. Gruppo Bertolaso is represented in the U.S. by ColloPack Solutions LLC, which worked closely with Kendall-Jackson as the project progressed.
The new multi-head cleaner, 60-head filler and six-head corker on Line 1 are individually driven by servo drives that electrically synchronize the machines for smooth bottle handling. Each machine has a feed screw and starwheel infeed and an exit starwheel.
The bottles are rotated back into an upright position as they approach the cleaner discharge and exit the machine onto the conveyor. The discharge starwheel is fitted with a safety device that stops the rinser in case a jam occurs.
Next, the bottles enter a 60-valve low-vacuum/gravity filler. In this process, the starwheel places the entering bottles onto individual bottle pedestals that rise as the machine rotates and push the bottles up against the fill valves. The fill spout enters the bottle and a vacuum is drawn to remove gas and any residual air that might be present. As the turret continues to rotate, the vacuum valve closes, and the fill valve opens and admits the wine.
As a bottle nears the discharge, the pedestal descends, allowing the fill valve to close. Bottles discharge through the starwheel.
Bottles then travel to the corker. Kendall-Jackson uses corks on all 750-mL bottles. All red wines have natural corks, while white wines will use natural and synthetic corks. All 375-mL bottles have screw caps.
As the bottles enter the corker, they again are placed on individual pedestals that lift them against fittings, where they go through a three-step process. A vacuum is drawn, followed by inert gas injection, followed by another vacuum application. According to Collopack, this minimizes residual oxygen.
Corks are inserted into the bottles after the second vacuum application. The corks travel down a channel to the application head, where they enter the unit's compressor jaws and are pushed into the bottles. After the corks are inserted, the bottles discharge through the starwheel and exit the enclosure.
The 375-mL bottles bypass t he corker, exit the enclosure and travel through an existing Fowler Products Co. LLC screw capper. The plant was running 750-ml bottles during PD's vist, so the screw capper was not in operation.
Bottles travel to an accumulation table supplied by Emmeti that provides three min. of accumulation time should there be a problem with the capsular or down-stream labeler.
From the accumulation table, the 750-mL bottles travel to capsule applicators. The 375-mL bottles bypass the capsulars.
The bottles then enter the 18-head horizontal turret that spins the capsules, without wrinkles or creases, tightly against the bottles. Each spinner has eight rollers that rotate to smooth the capsules around the bottles.
The capsules are an aluminum/poly/aluminum laminate supplied by Maverick Enterprises Inc.
A photo eye inspects the bottles as they leave the turret to ensure that the capsules are applied properly, and rejected bottles are gently pushed onto a take-away conveyor. The bottles on both lines then have front and back pressure-sensitive labels applied by Krones Inc. Autocol labelers.
Bottles leaving the labeler on Line 1 pass through a CI Vision system from Mettler Toledo that detects bottles with labels that are skewed, torn or improperly oriented. Bottles on Line 2 go through a Filtec inspection system from Industrial Dynamics Co. Ltd.
PARTITIONS INSERTED AFTER BOTTLES ARE PACKED
From the labelers, the bottles travel through continuous dividers that separate them into three lanes entering the case packer. Line 1 has a unit supplied by Emmeti, while Line 2 uses an older existing Krones separator.
Both lines are equipped with new Emmeti model Eagle 10/3 case packers. Cases are erected by a machine supplied by *Bortolin Kemo S.p.a., which is also represented by ColloPack Solutions, and are delivered to the packers on conveyors.
The case packer loads three cases at a time. After 36 bottles enter the pick-up zone, a bar holds back the incoming bottles to avoid back pressure on the bottles during the pick-up cycle. The system eliminates any contact between bottles and guides, thus avoiding any bottle and label damage after the pick-up.
A case centering device in the case packer ensures that it is positioned correctly to receive the bottles and a sensor detects the presence of the case. If a case is missing or not properly positioned, the machine automatically stops. Additional sensors allow the machine to restart only when the right number of cases are in position and stop the machine if a jams occurs outside of the case packer.
Low maintenance is standard with Emmeti's self-lubrication guides and supports. Grease cartridges that last for about two years provide automatic greasing of linear guides.
A unique feature of the case packers at Kendall-Jackson is that the partitions are inserted after the bottles have been placed in the cases. This eliminates label scuffing that occurs when bottles are packed into cases that contain partitions.
Partitions are inserted by a machine from Bortolin Kemo S.p.a The chipboard partitions are c ontained in a magazine on the machine, and vacuum cups extract one partition at a time and open it when a case enters the machine. An arm extends and places the partition over the bottles in the case, after which the case conveyor vibrates to settle the partition completely.
Kendall-Jackson is currently using full-height partitions to impart extra stacking strength, but the system can also insert shorter partitions if desired.
As the cases leave the partition inserters, *Markem-Imaje Model 5000 inkjet printers apply date codes and lot information. The cases then travel over Mettler Toledo Micromate checkweighers that essentially make sure each case contains the correct number of bottles. The cases are transported up a spiral conveyor from Emmeti and are conveyed to the palletizers.
Bortolin Kemo S.p.a, +39-0434-922010. www.bortolinkemo.com
ColloPack Solutions LLC, 707-258-3940. www.collopack.com
Emmeti USA, 813-490-6252. www.emmetiusa.com
Fowler Products Co. LLC, div. of Pro Mach, 877-549-3301. www.fowlerproducts.com
Gruppo Bertolaso, S.p.a., +39-0442-450111, www.bertolaso.com
Industrial Dynamics Co. Ltd., 310-325-5633. www.filtec.com
Krones Inc., 414-409-4000. www.kronesusa.com
Markem-Imaje, 866-263-4644. www.markem-imaje.com
Maverick Enterprises Inc., 707-463-5591. www.maverickcaps.com
Mettler Toledo, 614-438-4511. www.us.mt.com
O-I, 567-336-5000. www.o-i.com
Robino & Galandrino S.p.a., +39-0141-821411. www.robinoegalandrino.it
Saint-Gobain North America, 610-341-7000. www.saint-gobain-northamerica.com
Verallia North America, 707-437-8700. www.us.verallia.com
No related content found.